No products
Bevel sets
Viewed products
-
Universal tuning set
For accurate steering and...
Last Product Reviews
Universal tuning set
SET20
New product
For accurate steering and optimal manoeuvrability
More info
A smooth edge base, free of rust, markings, without too much scoring and no overlap of the base, guarantees manoeuvrability and optimal steering of ski and snowboards. For this reason, it is recommendable to polish the underside of the edge little but often, in particular, before each sharpening of the edge side.
The SET20 is ideal for this for two reasons:
-
The diamond file is double-sided, one side a fine grit (size 400) for polishing and the other grit size 200 for grinding (before polishing) where the edge is fairly damaged.
-
For high precision the diamond file is used in the filing guides for a side edge angle of 0.5° (slalom) or 1° (all-round and giant slalom).
-
Using our guides, it is easy to slide the file to prevent wear of the diamond in grooves which would round the edge.
Pack content
-
72.15 CHF1 x Two-sided long diamond file 200/400,...
(0)
Diamond grit size 200 und 400, long and resistant, adapted to the bevel file guide
72.15 CHF -
9.70 CHF -
9.70 CHF
Reviews (2)
|
Sébastien
mar 4, 2019 |
Un set indispensable
Un set indispensable pour un affûtage correcte de vos skis : permet d'accroître la maniabilité du ski tout en limitant l'usure de la carre et la quantité de métal à enlever lors du passage de la lime sur le côté de la carre.
Facile d'utilisation et efficace!
|
|
Recommended to buy:
Yes
|
|
T Florian
fév 27, 2019 |
good
good
|
|
Recommended to buy:
Yes
|
Foire aux questions (FAQ)
At each sharpening, we advise you to do 3 to 4 round trips with the long grain 400 diamond file. This removes roughness.
When there is noticeable damage, it must be removed or reduced with the long grain diamond file 200 and then finished with the long grain 400 diamond file to polish the underside of the edge.
If structures (which are necessary for the proper functioning of the base plate) are under the edge, grinding them out with a long grain 200 and then 400 grit diamond file is essential for the proper functioning of skis and snowboards.
Be careful, do not use long diamond files without lime guides!
The ideal is to file the first time and later to use Roto-Finish.
After filing, there is no need to fine-tune with Roto-Finish.
However, for the competition, especially if the snow is very cold and fine a polishing with Roto-Finish 400 then 800 will improve the glide.
When you have skied for a few days on soft snow that has very little rounded edge, it is not necessary to file. You can then limit yourself to three or four trips with the Roto-Finish 400.
When you've been skiing for a day or two on hard snow, you can sharp with the Twin Roro Concept, which consists of 10 to 12 round trips to the Roto-Finish 200 followed by polishing with the Roto Finish 400.
This polishing will be done either by 6 round trips with the roto-Finish 400 set to a degree less than the Roto-Finish, or without changing the angle (same angle as the Roto-Finish 200) but with a dozen or so back and forth.
If by 12 round trips to the RF200 you have not found the cutting edge, add some back and forth. If it is still not sharp it means that your edge is quite rounded and it is better to make a sharpening file.
In general, if you don’t do frequent sharpening use the file.
This is a personal practice that also varies depending on the ski models and / or the quality of the snow. Some do not round, others little and others more and this on different lengths. In general, we avoid rounding skis slalom and personally I do not round in heel even when it comes to longer skis.
For snowboards, it is advisable to round the front of the edge "front side" about 15 cm.
Also look question “Is it necessary to remove the lip with an eraser after using the Roto Finish for sharpening the edges of skis or snowboards?”